Showing 81–96 of 232 results
-
Replacement 2N3906FS-ND Transistor
$3.00PNP 200 mA transistor. As used in the MSStim V2.2 and later.
Add to cart -
555 Timer IC – through hole
$3.00The classic 555 timer integrated circuit, in an 8 pin DIP package. This little chip has plenty of uses. In the MegaSquirt lineup, the older Stim boards used it to generate an RPM signal, and the DIYPNP uses it in its knock circuit. See the MS1/Extra manua...
Add to cart -
-
CANEGT 8 Channel Thermocouple Interface
$378.69The CANEGT 8 Channel Thermocouple Interface allows you to monitor up to 8 K-type thermocouples AND up to 8 Innovate wideband devices over an Innovate Log Chain, and can transmit the data to a MegaSquirt-II, MegaSquirt-III, MicroSquirt, MSPNP, or MS3Pro o...
Read more -
CP-102A-ND Power Jack Connector
$3.00Replacement CP-102A-ND power jack connector. 5.5 mm OD, 2.1 mm ID. Used on the Stimulator, JimStim, and DIYPNP to connect to a power supply.
Add to cart -
QuadSpark Four Channel Ignition Module
$104.99Waterproof and capable of handling plenty of current, Quadspark makes an ideal ignition module for up to 4 coils. We have moved to Ecospark IGBTs for the main drivers, as Bosch no longer supplies BIP373 drivers. Each of the 4 channels can act independ...
Add to cart -
Power & Ground 14 Gauge Bundle 20′
$69.99Need some heavier wiring for power and ground? This 14 gauge automotive-grade wire can handle up to 20 amps per wire and use high temperature TXL insulation to stand up to high temperatures under the hood. We include four 20' lengths of wire: Sol...
Add to cart -
497-2055-5-ND RS232 Transceiver
$3.00Replacement 497-2055-5-ND RS232 transciever, 16 pin DIP package. Used as U6 in V3.0 and V2.2 MegaSquirts. This is a drop-in replacement for the MAX232.
Add to cart -
HSD-4 Channel High Side Driver
$109.99Have an application with a lot of small solenoids that need 12V power and rapid switching? Don't want the expense of a bank of four separate solid state relays, each rated for five times the current each solenoid needs? This module lets you run up to four...
Add to cart -
MegaSquirt Boost Control Mod Kit
$9.99Give your Megasquirt the ability to drive a boost control solenoid double up it's duty as an electronic boost controller. Includes all parts required to build the MSnS-E boost control circuit on your V2.2, V3.0, or V3.57 PCB, including FET, resistors, hea...
Add to cart -
460 Piece Weather Pack Kit
$100.00Our 460 Piece Weather Pack kits contains everything you need to get your project done right! We've used other connector kits available on the market in projects around the shop, they never quite met our expectations to be honest. So in typical DIYAuto...
Add to cart -
755 Piece Weather Pack Kit
$145.00Our Weather Pack kits contains everything you need to get your project done right! We've used other connector kits available on the market in projects around the shop and they never quite met our expectations. So in typical DIYAutoTune style, we stepp...
Add to cart -
6 Circuit Race Car Switch Panel
$114.00Six circuit race car switch panel with heavy duty switchgear. This includes one momentary switch for your starter, and five lighted on-off switches. The on-off switches have resettable circuit breakers instead of fuses, so if you need to get your race veh...
Add to cart -
4N25 Optoisolator – V3.0 U3
$3.00Replacement 4N25 optoisolator. Used as U3 in the V3.0 kits and U4 in the V2.2.
Add to cart -
IXDI604PI FET Driver – V3.0 U4
$3.99IXDI604PI dual inverting MOSFET driver. Replaces the IXDI404PI in the original bill of materials. This is U4 in a V3.0 board, U7 in a V2.2.
Add to cart
